Rif. 8N   Rif. 44BP   Rif. 34BP

Ref. 8N
Insulators
Robust, locks the tape without damaging it, thanks to its two screws in plastic material. If you want to fix it on a wooden pole just two screws (Ref. 8V).

 

Ref. 44BP
Tensioner
In the bipolar System the  tensioner Ref. 44BP can function as tensioner, insulator, buckle and T buckle to output a third tape to the internal division of the paddock.

 

Ref. 34BP
Buckles
Even the buckles was thought for the tape bipolar.

Rif. 11XBP   Rif. 12   Rif. 15BP

Ref. 11XBP
Bi-Polar Gate Handle
This handle has the terminal isolated. Can be attached to the insulator Rif. 10V

 

Ref. 12
Big Gate Handle
Bigger than Ref. 11XBP, can attached to the tensioner Ref. 44BP

 

Ref. 15BP
Bi-Polar Little Light
is an insulator type Rif. 8N that lights up to indicate the current is flowing.

Rif. 11XBP   Rif. 12   Rif. 15BP

Ref. 12P
Insulated handle
It has the same principle as Ref. 12 but smaller and more manageable

 

Ref. ADD
Nut Driver
With just one tool, thanks to this adapter you can use your screwdriver and screws for both the anchor bolts Hexagon turnbuckles Ref 44

 

Rif. CLIPSBP
Round Keeper Clip
With this clip you can fix the tape access.

Connections

The tape must be positioned with the green part facing up, and the brown (ground) at the bottom. Even the connectors follow the same principle:

• green wire connected to the green belt;
• brown wire connected to the brown belt;

To reduce the connections it is recommended to design the paddock with a single door and in correspondence of a tensioner.

For all connections you must have:

• the same length of the brown and green cable, also considering  the distance between the energizer and the fence and the distance between the tensioner of the same pole increased by 15cm
• 1 Power connecting clips
• 4 Power connecting clips for each tensioner where there are connections (8 for a rectangular paddock at two heights and a gate)

In the Bipolar electric fence system airbags the tensioner Ref 44BP is both tensioner, insulator, buckle and T-buckle for the release of a third tape to the internal division of the paddock.

Rif. 44BP   Rif. 44BP   Rif. 44BP

Ref. 44BP
used as a start

 

Ref. 44BP
used as a third way

 

Ref. 44BP
used as the buckle

How to install this system

1. install the poles every 5 meters (reduce the distance in windy land), use poles of larger cross-section in the corners, the departures of the fence and the points of union of two tapes

2. secure all of the insulators Ref 8V on wooden poles

3. set in the corners always on wooden poles of diameter 10cm-12cm with tensioners Ref 44BP don’t close it completely in order to be able to enter the tape

4. prepare tensioners Ref 44BP with the necessary cable connections
• Place the plates align the holes with the studs provided
• fix the lugs on the plate
• fix the power connection clips on the teflon cable
• Insert the end of the tape making sure that the green part is upward and the brown is down
• secure the front of the tensioner Ref 44BP and close with the screws
• fix everything on the poles of departure of the fence and close all with a key of 10

5. once fixed the tensioner starting to insert the tape in all the insulators Ref 8V up to the next corner

6. insert the tape into the corner tensioner, tighten the ribbon in order to keep the tape until it is completely fixing the tensioner

7. repeat step 5 and 6 until the end of the paddock

8. the gates will be made with the bipolar tape and Special handle Ref 11XBP to be fixed to the insulator Ref 10V fixed on wooden pole but away from the starting tensioner

Accessories are available for every need

Ask us for a quote to build every paddock you want!